Feeds:
Posts
Comments

Archive for May, 2021

Inglorious colour

I did promise it would be pretty tatty.

So alongside the rebuilding, I’ve completed the prototype container, and it isn’t looking too bad considering it’s essentially a drainpipe wrapped in paper. The paper came close to causing a lot of trouble this time; glue only takes so long to dry after all, and it managed to dry quicker than I could pull all the awkward bits through the various gaps in the frame. As usual I’m relying on my readers to be too unobservant or polite to comment on the way the writing and hazard symbols are at slightly different heights on each side. I’m also not even going to show you the underside of the tank.

Current plans include some kind of detachable frame for version 2.0. so it can go on after the tank covering is completed. Somehow.

Obsession with rust continues: I used the stippling method previously seen on a railcars some years back, as the hairspray method would risk damaging the paper on the tank. I think there’s possibly a bit too much stipple; it’s very hard to know when to stop.

Still, now I’ve got a passable container to lurk in the background occasionally, now all I have to do is finish a non-bendy wagon for it to travel on…

Read Full Post »

Heavy(ish) industry

I’ve got a sort of production line running to make the new generation of low loader container/swap body wagons. They are somewhat heavier than the previous versions to avoid banana wagon syndrome and made them a tad longer while I was at it.

Observant readers will have noticed that there are three instead of the two I was building earlier. I think the railway would be into containers in a big way so an extra wagon won’t hurt. And if the first one doesn’t work very well I can always call it a “prototype” and build the other two differently.

After previous attempts cutting the frames around a template resulted in something that looked like a piece of badly cut cheese I used a jig this time, which sounds fancy but basically was a few bits of card to hold the plastic bits in place while I glued them together. Even that description makes it sound more complex than it was.

The result isn’t that pretty, as the two bits on the bottom of the picture show, Unfortunately it was also not entirely accurate, but I laminated them onto other bits of plastic (middle) on either side to add strength and hide the worst of the gaps. Now I’ll add bits on the top and bottom to make them into rather substantial I-beam girders.

Then if they aren’t shaped like something an orangutan would eat next week, I’ll add the cross pieces.

Read Full Post »

There’s always an awkward stage, and in my case it seems to be the start of painting a model, when the basic colour is there but the shading and weathering isn’t. Instead of the model taking in the form of “reality in miniature” it looks like a badly painted concoction of bits of pipe and wire. In this instance forgetting to take a picture until I’d made the first attempts at a black wash didn’t help either. Fortunately this swap body is supposed to be fairly tatty so I have a fair bit of freedom to hide this.

it is also the point where I start to try and add the details and other bits in the hope that it will gradually look less like a badly painted concoction and more like a part of the story I’m trying to create, or at least distract the eye from the worst of the problems. To this end I’ve spent a couple of evenings finding out more than a same person would want to know about tanker chemical codes and hazard warning symbols.

Also, notice the thrilling debut of a colour other than green.

Read Full Post »

Going Bananas.

There have been sinister goings on up on the workbench shelf while your correspondent was innocently working on the overly complicated swap body; the two well wagons made a conspiracy to go all banana shaped. I’d wondered why the clearance above the rails was so small, until I looked lengthways and realised they were quietly turning into something that only Robin hood could find a use for.

It the bend above isn’t obvious, here’s a straight line in comparison:

It’s not just scraping the rails, it’s dragging along in the ballast…

Enquiries online revealed this was a common problem with well wagons. Now I think about it, there was a similar issue with the original wood wagon, but this was solved on the second incarnation by the addition of some truly massive side frames . The current issue is rather more serious and the general opinion seems to be that it is best solved with a brass rod along the inside of the lower part of the frame, glue, lots of clamps, and hope.

On the other hand, since I started building these wagons, more information has come in showing that not only are the originals considerably more substantial than I previously thought, but they are also somewhat longer, so I think it’s time to cut my losses and start again.

After some discussions with people that know what they are doing: this seems to be the way to go forward…

Here we go again…

Read Full Post »

Grey Swapbody

As the title suggests, the swapbody is now in grey primer.

Try to contain* your excitement.

*See what I did there?

Read Full Post »

The Swap body prototype is now structurally complete, which has answered a few questions about the sizes and general dimensions, but opens a couple more such as “What will it carry?” and “Why on earth didn’t I just make something simple like a parcel container?”

I’m leaving the second question as it is impossible to answer, but the container will be a rather nondescript carrier of “diesel fuel” operated by a company contracted by the Körschtalbahn. Like a lot of German railways, he KÖB will have a small maintenance and fuel facility at the distant end of the line, rather than at the connection with the national network as was more common in the UK. This is because a lot of these lines are paid for by the local authorities which generally prefer to bring as much maintenance in house as possible, on the basis it brings employment and keeps money in circulation.

This means that this container will make occasional appearances when the shed needs a delivery, and will probably find itself probably tacked onto a regular freight or passenger train as required. Other than that it will be kept well hidden so as not to disturb the public…

Read Full Post »